Schneider Electric Xantrex XW Instalační příručka Strana 67
- Strana / 166
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Step 5: Installing Additional Inverters
975-0239-01-01 2–37
This manual for use by qualified personnel only
Step 5: Installing Additional Inverters
Installation Steps
To install multiple inverters:
1. Disconnect all power from the system.
2. Mount additional inverter(s). See “Step 1: Installing the Mounting Plate” on
page 2–5 and “Step 2: Mounting the Inverter” on page 2–7.
3. Install the Xantrex XW Conduit Box. See “Step 3: Mounting the Xantrex XW
Power Distribution Panel and Xantrex XW Conduit Box” on page 2–8.
4. Install AC sync cable(s) as required. See “Xantrex Xanbus and AC Sync
Cable” on page 2–49.
5. Install a Xantrex XW System Control Panel to configure programmable
settings and to name specific network components (e.g., XW1, XW2 etc.).
See “The Xantrex XW System Control Panel” on page 5–2.
6. Convert the Xantrex XW Power Distribution Panel to accommodate the extra
inverter by installing the additional breakers and components. See page 2–38
for instructions on converting the Xantrex XW Power Distribution Panel to a
dual-inverter configuration. See page 2–44 for converting the Xantrex XW
Power Distribution Panel to a triple-inverter configuration.
7. Attach Bypass interlock plate to distribution panel cover.
8. Connect DC wiring. See Figure 2-27 on page 2–39 for dual-inverter
configurations and Figure 2-31 on page 2–45 for triple-inverter
configurations.
9. Connect AC wiring. See Figure 2-29 on page 2–41 for dual-inverter
configurations. For triple-inverter Configurations, see Figure 2-32,
“Triple-Inverter AC Breaker Arrangement and Wiring Enlargement with Dual
AC Input Sources” on page 2–46 or Figure 2-33, “Triple-Inverter AC Breaker
Arrangement and Wiring Enlargement with a Single AC Input Source” on
page 2–47.
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Související produkty a manuály pro Bezpečnostní systémy pro řízení přístupu Schneider Electric Xantrex XW
(58 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.049 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce