Schneider Electric ALTIVAR 58 TRX Instalační příručka Strana 50
- Strana / 126
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
© 1998–2003 Schneider Electric All Rights Reserved
Chapter 2—Menus VVDED397047USR6/03
3—Drive Menu 06/2003
50
Sw Freq -kHz SFr
Selection of switching
frequency. The range depends
on the SFt parameter.
The maximum operational
frequency (tFr) is limited
depending on the switching
frequency:
LF: 0.5-1-2-4
kHz
HF1 or HF2:
4-8-12-16
kHz
[5]
LF: 4 kHz
HF1 or
HF2:
(depend-
ing on
controller
rating)
SFr (kHZ) 0.5 1 2 4 8 12 16
tFr (Hz) 62 125 250 500 500 500 500
Noise Reduct nrd
This function randomly
modulates the switching
frequency in order to reduce
audible motor noise.
No - Yes
Yes if SFt
= LF
No if SFt
= HF1 or
HF2
NOTE: Special
Mot. is not
available in
variable torque
mode except in
the 125–500 hp
drive controllers.
After enabling this
parameter, the IR
compensation
parameter
appears in
Menu 2. For
1/2 –100 hp drive
controllers, setting
SPC to PSM while
in the material
handling macro
and then selecting
the variable torque
macro will leave
the PSM setting
enabled.
Special Mot. SPC
Special motor adaptation
No - Yes -
PSM
No
This parameter should be set to Yes when using special
motors such as synchronous permanent magnet motors,
synchronous wound field motors, or synchronous
reluctance motors. This parameter should also be enabled
if using one
drive controller to control multiple motors in
parallel. Installation of individual motor thermal protection is
required when using the drive controller to control multiple
motors in parallel.
The PSM setting is intended to be used when the motor
connected to the drive controller is less than 25% of the
drive controller’s nominal current rating. It may be
necessary to disable output phase loss protection, OPL.
Installation of motor thermal protection is required in this
type of application.
Also, the PSM setting can be enabled to allow for open
circuit output voltage testing.
Enabling the SPC parameter increases the IR
compensation adjustment range from 0 to 800%.
Table 11: 3—Drive Menu Parameters (continued)
Parameter Code Description
Adjustment
Range
Factory
Setting
[1]
Depending on the position of the 50/60 Hz switch. Ensure that the switch setting
matches the input frequency (see page 14).
[2]
I
n
= drive controller constant torque output current rating shown on the drive controller
nameplate.
[3]
The factory setting depends on the macro-configuration used: No for Material
Handling, Yes for General Use and Variable torque.
[4]
This parameter is not available on 125–500 hp drive controllers.
[5]
Refer to the drive controller instruction bulletin, VVDED397048US, for duty cycle
ratings of the drive controllers.
★ These parameters are available only with the I/O extension card installed.
Menu
3
- Keypad Display VW3A58101 1
- TABLE OF CONTENTS 3
- Table of Contents 06/2003 4
- 06/2003 Table of Contents 5
- 06/2003 Introduction 7
- Keypad Display 11
- • Local command 11
- Keypad Display 06/2003 12
- Retaining Screw 12
- 06/2003 Keypad Display 13
- 50 Hz 60 Hz 14
- 50/60 Hz switch 14
- 06/2003 Access Levels 19
- Figure 6: Menus 20
- Access Levels 06/2003 22
- 06/2003 Language Menu 23
- Validate? ENT/ESC 25
- CUS:Customize 26
- Language 27
- Macro-Config 27
- 40 HP 200/240 V 27
- 1-DISPLAY MENU 27
- 1—Display Menu 28
- 2—Adjust Menu 29
- Handling Macro-Configuration 35
- Use Macro-Configuration 37
- Reassignment 39
- Reassignment (continued) 40
- 3—Drive Menu 41
- 3—Drive Menu 06/2003 42
- Set the CoS parameter to the 44
- T1 = 1/Acc 48
- T1 = 1/Dec 48
- 4—Control Menu 52
- ATV58 TRX terminal strip 53
- 24 V LI1 53
- LI1: Forward 53
- LIx: Reverse 53
- AOL AOH 20 55
- Parameter 55
- 5—I/O Menu 58
- 5—I/O Menu 06/2003 64
- 06/2003 5—I/O Menu 65
- LI1 LI2 LI3 LI4 +24 AIX 67
- —Drive menu 71
- • DC injection current 72
- • Brake release current 72
- • Nominal motor current 72
- Input Code Range Description 75
- • If AI3 = 10 V: limit = TLI 77
- T = non-adjustable delay 79
- • Brake release time (brt): 81
- • Brake engage time (bEt): 81
- 6—Fault Menu 85
- Table 21: 6—Fault Menu 86
- 7—Files Menu 89
- Table 22: 7—File Menu 90
- 06/2003 7—Files Menu 91
- Parameter Code Description 92
- Factory 92
- Password Fault 93
- 8—Communication Menu 94
- 8—Application Menu 94
- Red FAULT LED 95
- Maintenance 96
- Precautions 97
- Do not use 100
- Fault Codes and Messages 103
- ≥ 200 ms) 106
- Trip Point Reset Point 107
- VVDED397047USR6/03 Altivar 109
- Table 35: Menu 7—File Menu 112
- (continued 113
- (continued) 114
- Menu 6 – FAULT Menu (page 82) 115
- Menu 7 – FILES Menu (page 86) 115
- Catalog No. Description 117
- 91598106011107 126
Související produkty a manuály pro Měření, testování a kontrola Schneider Electric ALTIVAR 58 TRX
(8 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.171 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce